Popular Posts

Showing posts with label Job interview or viva topics for electrical and electronic Engineers. Show all posts
Showing posts with label Job interview or viva topics for electrical and electronic Engineers. Show all posts

Electronics and Electrical Engineering interview Question and Answers for fresh engineers (Part 8)


Electronics and Electrical Engineering interview Question and Answers for fresh engineers (Part 8)

 In this topic we know about the substation and its some requirements for setup.


 Question: What do you mean by substation? Give some details.


Answer: The electric power is now generated in the form of alternating current. The electric power is produced in the power station, which is generally very far from the consumer premises. So, the generation, transmission and distribution are facing much difficulty. It is distributed to the consumer or user by the help of a very large interconnected network. In the network it is very important to change some characteristics for transmitting and distributing the electric power properly. Such as, ac to dc conversion (by using thyratron and mercury arc rectifier), voltage up or down (If the generating voltage is 11kv then transfer it to the high voltage range of 220kv), frequency change, power factor correction and improvement. This change needs a setup of some apparatus properly, in short this types of setup is called substation.

          The assembly of electrical apparatus whose purpose is changing the some major characteristics of the electric supply system is called substation.


            The substation is very important for achieving the continuity of supply to the consumers. In some cases the ac is need to convert in dc for running the dc motor, traction, electroplating processes this type of conversion is performed by the sub-station (ignitron).

electronics and electrical engineering interview question and answer: sub-station
SUB STATION


Question: What are the basic requirements for setup a substation? Or which conditions are considerable for setup a substation?


Answer: The continuity of electric energy supply system is solely depending on substation. So, enough care should be taken when designing and set upping a sub station in a suitable place.

Some points are as follows,

·        The substation must have the chance of easy operation and maintenance.
·        The place must be proper for setup a substation. It must be setup near the centre of the load.
·        The substation must have enough safety apparatus or safety setup. There must be enough chance for running the maintenance and clearing process. Also there should be setup for fire protection.
·        The system must be reliable. When designing protected gears and other instruments must be included. The construction process also maintained properly for reliable operation.
·        The capital cost must be as low as possible.

-- - - - -- --- - -- - - -- - - - -- -  -- - - - - -  -- - - - -- - - - - - - - - 
We will give more important questions and answers for electrical engineering interview very soon. Please subscribed to RSS feed or Email feed. We need your help for the betterment of the site. Please give comments and tell us what’s your opinions and needs from us. We will try to give your required things.

Job interview Topics for Electrical and electronic Engineers (Part-2).


Electrical Engineering interview question and answers:Job interview or viva Topics for Electronics and Electrical Engineers (Part-2).


In this topic we discuss about Load Curve,Demand Factor and Load Factor.



4. Load Curve:

The curve which shows the variation of load on the electrical power station with respect to time is known as load variation curve or simply load curve.

5. Importance of Load Curve:

                  
  • The Daily Load Curve gives the information of load on the power station during different running hours of the day.
  • The number of unit’s generation per day is found from the area under the daily Load Curve.
  • Average load is found from the Load Curve.

Average load= [Area (KWh) under daily load curve/24 hours]

  • The maximum demand of the station on that day is found from the highest point of the daily Load Curve.
  • The size and the number of generating units can be determined from the load curve.
  • This Load Curve helps to determine the operation schedule of the station. In that case when all the units or the less units needs to running is found.

6. Demand Factor:  

The ratio of maximum demand and connected load on the power station is called as demand factor.

Demand Factor= [Maximum Demand/Connected Load]

  • In the power station Maximum demand < Connected Load.
  • Demand Factor < 1
  • Demand Factor is very important in determining the capacity of the plant equipment.

7. Load Factor:  

The ratio of Average load and the Maximum demand in a given period of time in a power plant is known as load factor.

Load factor = [Average load/ Maximum demand]

  • In a power plant Average load < Maximum demand
  • Load factor<1.
The Load factor is very important for determining the cost of per unit generation of power.




-- - - - -- --- - -- - - -- - - - -- -  -- - - - - -  -- - - - -- - - - - - - - - 
We will give more important questions and answers for electrical engineering interview very soon. Please subscribed to RSS feed or Email feed. We need your help for the betterment of the site. Please give comments and tell us what’s your opinions and needs from us. We will try to give your required things.

Electronics and Electrical Engineering interview Question and Answers for fresh engineers (Part 9)

Electronics and Electrical Engineering interview Question and Answers for fresh engineers (Part 9)

In this topic we will know about motor protection

In the nameplate of the motor we see IP XY . i.e. IP 55
Example: With the IP rating IP 23, 

  • 2 describes the level of protection from solid objects and 
  • 3 describes the level of protection from liquids.

IP stands for 

Ingress Protection Ratings

 IP rating normally has two (or three) numbers:

  1. Protection from solid objects or materials
  2. Protection from liquids (water)
  3. Protection against mechanical impact 

specifying the environmental protection the enclosure provides.
Ingress Protection (IP) ratings are Introduced by the European Committee for Electro Technical Standardization .

 NEMA IEC 60529 Degrees of Protection Provided by Enclosures - IP Code,


IP First number - Indicates the Protection against solid objects. Which we indicates as X in the example

0 No special protection
1 Protected against solid objects over 50 mm, e.g. accidental touch by persons hands.
2 Protected against solid objects over 12 mm, e.g. persons fingers.
3 Protected against solid objects over 2.5 mm (tools and wires).
4 Protected against solid objects over 1 mm (tools, wires, and small wires).
5 Protected against dust limited ingress (no harmful deposit).
6 Totally protected against dust.

IP Second number -Indicates the Protection against liquids.Which we indicates as Y in the example 

0 No protection.
1 Protection against vertically falling drops of water e.g. condensation.
2 Protection against direct sprays of water up to 15o from the vertical.
3 Protected against direct sprays of water up to 60o from the vertical.
4 Protection against water sprayed from all directions - limited ingress permitted.
5 Protected against low pressure jets of water from all directions - limited ingress.
6 Protected against temporary flooding of water, e.g. for use on ship decks - limited ingress permitted.
7 Protected against the effect of immersion between 15 cm and 1 m.
8 Protects against long periods of immersion under pressure.



Example - IP 35

An electrical socket rated IP22 is protected against

  • Protected against solid objects over 2.5 mm (tools and wires).
  • Protected against low pressure jets of water from all directions - limited ingress.
IP stands for  Ingress Protection Ratings www.vivasolve.blogspot.com
IP stands for 
Ingress Protection Ratings

IP Third number - Indicates the Protection against mechanical impacts .

Its not used in normal cases. 

the third number is not available in IEC 60529

0 No protection.
1 Protects against impact of 0.225 joule
(e.g. 150 g weight falling from 15 cm height).
2 Protected against impact of 0.375 joule
(e.g. 250 g weight falling from 15 cm height).
3 Protected against impact of 0.5 joule
(e.g. 250 g weight falling from 20 cm height).
4 Protected against impact of 2.0 joule
(e.g. 500 g weight falling from 40 cm height).
5 Protected against impact of 6.0 joule
(e.g. 1.5 kg weight falling from 40 cm height).
6 Protected against impact of 20.0 joule
(e.g. 5 kg weight falling from 40 cm height).


We will give more important questions and answers for electrical engineering interview very soon. Please subscribed to RSS feed or Email feed. We need your help for the betterment of the site. Please give comments and tell us what’s your opinions and needs from us. We will try to give your required things.

Job interview and viva Topics for Electrical and electronics Engineers (Part-4).

Electrical engineering interview topic:Job interview and viva Topics for Electrical and electronics Engineers (Part-4).

In this topic we know about Power System Stability,Steady State Stability,Static Stability,Dynamic Stability and Steady State Stability Criterion

13. Power System Stability: 

 In the large power system there might be some disturbance always. The system has the tendency for the system to develop forces for bringing the system in a normal or stable condition. The ability of the system to obtain the normal or stable condition after getting disturbed is called Power System Stability.

The stability has mainly two types: 
1. Steady State Stability.
2. Transient Stability.

14. Steady State Stability:  

The ability of being stable after a small disturbance in the system is called Steady State Stability.

The Steady State Stability is concerned with the very small power changes .which are changed gradually.

The Steady State Stability has two types:
1. Static Stability
2. Dynamic Stability.

·        Static Stability: 

In the Static Stability there is a large duration phenomenon with small disturbance. This is the inherent stability that can achieve with out the help of automatic control devices.

·        Dynamic Stability: 

In the Dynamic Stability there is a small duration phenomenon with large disturbance. This Dynamic Stability refers to artificial stability. This artificial stability is given to an inherently unstable system by the help of automatic control devices.

15. Steady State Stability Criterion:

The rate (dP/dδ) of the differential power increased is obtained per differential load angle increased. This are called as electrical stiffness or the synchronizing power coefficient of a synchronous machine. This is considered as the measure of the stability of the system.
The Steady State Stability has basically three Criterion or state.
When,
·        (dP/dδ) > 0 ; Direct State Synchronous Stability.
·        (dP/dδ) = 0 ; Steady State Stability.
·        (dP/dδ) < 0 ; The System is unstable.
----------------------------------------------------------------------
Thanks for your time. Hope we will give more important questions and answers for interview very soon. Please subscribed to RSS feed or Email feed.

Determine the efficiency & characteristic of a Shunt wound DC motor.



Objective:-To Determine the efficiency & characteristic of a Shunt wound DC   motor.

Theory:- The field coil and the armature windings are connected in shunt or parallel across the power source. The armature winding consists of relatively few turns of heavy gauge wire. The voltage across two windings is the same but the armature draws considerably more current than the field coil. Torque is caused by the interaction of the current caring armature winding with the magnetic field produced by the field coil. If the DC line voltage is constant, the armature voltage and the field strength will be constant. The speed regulation is quite good; the speed is a function of armature current and is not precisely constant. As the armature rotates within the magnetic field, an EMF is induced in its wining. This EMF is in the direction opposite to the source EMF and is called the counter EMF, which varies with rotational speed. Finally, the current flow through the armature winding is a result of the difference between source EMF and CEMF. When the load increases, the motor tends to slow down and less CEMF is induced, which in turn increases the armature current providing more torque for the increased load. Motor speed is increased by inserting resistance into the field coil circuit, which weakens the magnetic field. Therefore, the speed can be increased from “basic” or full-load, full-field value to some maximum speed set by the electrical and mechanical limitations of the motor.
The shunt motor is constant speed, medium starting torque & high running torque.

Equipments Required:-  
1. Power supply
2. DC Motor/generator
3. DC Voltmeter/Ammeter
4. Electrodynometer (fixed 240V ac)
5. Connection Leads
6. Tachometer
7. Timing belt

Connection Diagram:-


         





         


Table:
                         
E
(volts)
I
(amps)
SPEED
(r/min)
TORQUE
(N.m)
240


0
240


0.3
240


0.6
240


0.9
240


1.2











































































































































































Characteristic Curve:




















Calculation:

 Regulation =
 Pout =


Discussion: